How To Set Swr On Wilson 2000

This is why you use an external SWR meter for tuning your CB antenna.
How To Tune Your CB Antenna (Quick & Simple)
CB Antenna Tuning Methods Explained by CB World!
Wilson 1000 problem TEST magnet et coil…Le Spécialiste Du CB
Another high SWR issue solved on Wilson 5000
Tuning Wilson 2000 Trucker CB Antenna
This Is How To GET SUPER LOW SWR ON YOUR CB RADIO!!
- Related Articles:

This is why you use an external SWR meter for tuning your CB antenna.

Video taken from the channel: J Rich

How To Tune Your CB Antenna (Quick & Simple)

Video taken from the channel: Jerry Arbs

CB Antenna Tuning Methods Explained by CB World!

Video taken from the channel: CB World

Wilson 1000 problem TEST magnet et coil…Le Spécialiste Du CB

Video taken from the channel: Le Spécialiste Du CB

Another high SWR issue solved on Wilson 5000

Video taken from the channel: sramsdellwdm

Tuning Wilson 2000 Trucker CB Antenna

Video taken from the channel: Heavy Haul TV

This Is How To GET SUPER LOW SWR ON YOUR CB RADIO!!

Video taken from the channel: 1ROAD

THE SET UP If already connected, disconnect the coaxial cable from the radio. Connect the coax cable that normally connects to the back of the radio to the SWR meter connector marked "Antenna" or "Ant". Now, connect one end of the jumper cable to the back of the radio and the other end to the SWR meter connection marked "Transmitter" or "Xmit". Your SWR May Not Be What You Think Always Use Ohm Meter For Bonding Antenna Analyzer For Tuning Duration: 20:44. Fine Tune CB Shop 10,823 views.

If your coax cable has an open that is, the wire is broken and current can't flow through it you'll get off-the-chart SWR readings. Follow this guide to test your CB coax for problems. #9 Test Your Antenna for Defects / Opens. Just like potential coax problems, if the wire in your antenna is broken you'll experience high SWR. Has any body ever noticed how narrow banded wilson 5000 antenna's are? It is so narrow banded that when I set the swr's to flat on the bowl, they ended up being 1.4 on channel.

When I used to run the wilson 1000 I was able tune it flat from channel 1-40. Why is that, is it because the 5000 has different impedence or is it just an engineering flaw they had. For this you will need your meter and a short jumper of coax with the correct connectors on it (usually PL-259s).

Connect one end of the jumper to the back of your radio. Now connect the other end to the "Transmitter" socket on the SWR meter. The antenna's coax now connects to the "Antenna" socket on the meter.

Based on the type of CB antenna that you have, you will need to know how to tune your antenna. Antenna Tuning is VERY IMPORTANT! Tuning an external CB antenna is critical to optimizing your CB.

Turn the knob on the SWR meter labeled "SET" or "ADJUST" until the needle reaches the setting position at the end of its range. While still keying the microphone, flip the switch on the SWR meter to the "REF" or "SWR" position. Quickly record the reading given by your SWR meter and release the transmit key on your microphone. That sirio performer 5000 mobile antenna is awful close to a full sized 1/4 wave so I would expect it to perform 'close' to a a full sized antenna. If the antenna you are comparing it to isn't as 'long' as that sirio then I would expect there to be some differences in performance.

Connect the coaxial cable jumper to the SWR meter "Out" to the "Ant In" on the CB radio. If the CB has a built-in SWR meter, attach the coaxial cable from the Wilson 2000 antenna to the back of the CBs "Ant In.". Wilson Trucker 2000 CB antennas installed in 11:01. Wilson 1000, 5000, Stryker SR5K Magnet Mount Repair / Coax Upgrade CB Radio for Beginners Part 3 SWR Calibration on Cobra. I have a Wilson 5000 center load mounted to the left fender with 21 ft of 58 coax and can't get the swr under 2.8 on 1&40 Checked ground and coax with.

Heck, maybe you're just lazy and don't want to bother with a lot of the mounting headaches. In any case the Wilson 1000 and Wilson 5000 antennas offer excellent performance in a small and easy to mount package. I've always been able to get a SWR under 1.5 with either antenna and never had any problems with failure or defects.

List of related literature:

The RF Gain control on the receiver should be fully clockwise for minimum attenuation.
from The Electronics of Radio Cambridge University Press, 1999
The low-noise amplifier should be mounted on the antenna if it is wideband and at the receiver if it is tunable.
from The Technician's Radio Receiver Handbook: Wireless and Telecommunication Technology by Joseph Carr, Joseph J. Carr Elsevier Science, 2001
For ease of explanation, set the antenna length at 1" from the antenna top to the top of the attachment nut. 1.
from Donny's Unauthorized Technical Guide to Harley-Davidson, 1936 to Present: Volume Iii: the Evolution: 1984 to 2000 by Donny Petersen iUniverse, 2010
Receiver Test Setup When Antenna Is Active
from Manuals Combined: Electronic Warfare and Radar Systems Engineering Handbook: 2013, 2012, 1999, 1997 Plus Principles of Naval Weapons Systems, Satellites And Radar Fundamentals by Jeffrey Frank Jones,
Connect the antenna and ground plane to the spectrum analyzer by screwing the coax cable into the input port on the spectrum analyzer.
from RFID For Dummies by Patrick J. Sweeney, II Wiley, 2010
Open the hinged upper receiver from the rear.
from The World's Assault Rifles by Gary Paul Johnston, Thomas B. Nelson Ironside International Publishers, Inc., 2016
To use most receivers, you simply mount the antenna, connect the antenna to the receiver, and turn the receiver on.
from The Measurement, Instrumentation, and Sensors: Handbook by John G. Webster CRC Press, 1999
First, set the tuning knob on the receiver to the 10 o'clock position, and using the plastic tools included within the kit adjust the component L5 (variable inductor) until a loud tone can be heard.
from Getting Started in Radio Astronomy: Beginner Projects for the Amateur by Steven Arnold Springer New York, 2013
There is NOTHING, absolutely NOTHING, that you can do at the CB end of the system to lower the SWR at the antenna end.
from Screwdriver Experts Guide to Peaking Out and Repairing CB Radios by Lou Franklin CB City International, 1987
The next step is to determine the minimum RF level at the receiver input that will open the front end of the receiver (i.e. turn it on).
from Practical Variable Speed Drives and Power Electronics by Malcolm Barnes Elsevier Science, 2003